AETI Solves Wind Farm Arc-Flash Safety Risks

American Electric Technologies, Inc. (NASDAQ: AETI), the premium global supplier of custom-designed power delivery solutions for the traditional and renewable energy industries, today announced the introduction of the wind energy industry's first switchgear solution designed specifically to provide

FOR RELEASE 9 a.m. (ET)

February 24, 2010

AETI Solves Wind Farm Arc-Flash Safety Risks with Introduction of the Industry's First Wind Switchgear Solutions

HOUSTON/AUSTIN (February 24, 2010) - American Electric Technologies, Inc. (NASDAQ: AETI), the premium global supplier of custom-designed power delivery solutions for the traditional and renewable energy industries, today announced the introduction of the wind energy industry's first switchgear solution designed specifically to provide safer, more reliable, higher-performing wind farm operations.

Safety a Prime Wind Issue
The US Bureau of Labor Statistics reports 212 workers lost their lives in 2008 from contact with electric current. In 2007, 250 fatal worker injuries occurred and in 2006, 256 deaths were reported. These statistics include deaths from arc flashes, which are electrical explosions caused by low-impedance faults between ground and another voltage phase in an electrical system. Arc flashes tend to occur during initial power equipment start-up and during equipment maintenance. Injuries from arc flashes range from minor injuries to third-degree burns, blindness, hearing loss, nerve damage, cardiac arrest and even potential death. Approximately 65 percent of arc faults occur during electrical maintenance when the equipment doors are open and an operator is standing in front of the equipment. Conventional arc-resistant switchgear, which channels the arc flash through vents away from the equipment and the operator, has limited arc-management capability, significantly compromising wind farm maintenance worker safety in confined areas and putting assets at risk.
The Occupational Safety and Health Administration (OSHA) reports they investigated 32 arc flash-related accidents in 2009, 38 in 2008 and 25 in 2007. Some industry reports estimate that the average cost a company incurs for medical treatment on behalf of each arc-flash survivor is $1.5 million, and total costs of litigation could reach up to $10 million.
Industry-first wind farm switchgear designed for safety, performance and reliability
AETI is leveraging their 60 years of experience in deploying custom-designed power distribution equipment in the world's harshest environments with the company's wind farm services experience, to introduce new, 40kV wind farm switchgear at the Renewable World Energy Conference and Expo North America in Austin. The switchgear is designed specifically for the wind power industry, and breaks new ground in wind farm safety, performance and reliability.

Safety
AETI understands that more than 50 percent of arc faults injuries occur during electrical maintenance when an operator is standing in front of the equipment. By designing remote circuit breaker racking, maintenance workers can rack in and rack the circuit breakers from a safe distance away. The switchgear also incorporates a ground safety switch, interlocked with the circuit breaker, enabling the operator to ground incoming cables during maintenance, reducing exposure to accidental electrical back feed. Most significantly, AETI's wind farm switchgear provides protection for high impedance faults, where fault currents may not reach the required level to trip conventional breaker trip settings. The system uses proven light-sensing technology to detect the arc-flash, and sends a signal to open the circuit breaker, isolating the arc-fault within approximately 50 milliseconds.

Currently, the National Fire Protection Agency 70E guideline only requires special clothing and personal protective equipment be worn to mitigate the injuries. Even with these guidelines in place, companies would still need to rely on employees to consistently and correctly wear the gear, which does not always occur.

Performance
AETI's wind farm switchgear is designed to enable maximum wind farm power delivery to the grid. Unlike traditional 38kV switchgear with limited peak duty, AETI's switchgear provides 40kV power distribution at 3000A continuous duty, enabling more wind power to be delivered to the grid per collector line. The switchgear also has a 40kA interrupting rating, enabling wind farm developers to connect to high-capacity power grids.

Reliability
The AETI switchgear system is designed for wind farm reliability. By offering industry leading 170 kV basic impulse level (BIL), the substation and wind farm are provided increased resilience lightening strikes. The system also uses vacuum-based circuit breaker technology that eliminates use of toxic sulfur hexafluoride (SF6) gas and continual recharging maintenance services.

"We are pleased to bring our rich history of manufacturing first-rate power distribution gear to the wind and renewable energy markets," said John Skibinski, AETI's vice president of renewable markets and chairman of the American Wind Energy Association (AWEA) wind reliability task force. "We are even prouder to provide safer, higher performance and more reliable switchgear to the industry."

The company will be exhibiting at the 2010 Renewable Energy World Conference & Expo North America in Austin February 23-25 in Booth 159, and will be available to discuss the new 40kV arc-mitigating switchgear technology for safer wind farm deployments. Visit www.aeti.com/wind or email info@aeti.com for more information on AETI's portfolio of wind product and service solutions.

###

American Electric Technologies, Inc. (NASDAQ: AETI) is the premium global supplier of custom-designed power delivery solutions to the traditional and renewable energy industries. AETI offers M&I Electric™ power distribution and control products, electrical services, and E&I construction services, as well as American Access Technologies zone enclosures, and Omega Metals custom fabrication services. South Coast Electric Systems L.L.C., a subsidiary, services Gulf Coast marine and vessel customers.

AETI is headquartered in Houston and has global sales, support and manufacturing operations in Beaumont, Texas, Keystone Heights, Fla. and Bay St. Louis, Miss. In addition, AETI has minority interests in two joint ventures, which have facilities located in Xian, China and Singapore. AETI's SEC filings, news and product/service information are available at www.aeti.com.

Forward Looking Statements
Except for the historical and present factual information contained herein, the matters set forth in this document, including statements regarding the anticipated results of our international joint ventures are forward-looking statements within the meaning of the "safe harbor" provisions of the Private Securities Litigation Reform Act of 1995. There are many risks, uncertainties and other factors that can prevent the achievement of our goals or cause results to differ from those expressed or implied by these forward-looking statements including, without limitation, the risks inherent in doing business outside of the U. S. such as political, social and economic instability, currency fluctuations and conversion restrictions. These and other risks, which may impact management's expectations, are described in greater detail in filings made by the Company with the Securities and Exchange Commission. The Company assumes no obligation to publicly update or revise its forward-looking statements even if experience or future events make it clear that any of the anticipated results expressed or implied herein will not be realized.

Media Contact:
Ward Creative Communications for
American Electric Technologies, Inc.
713-869-0707
Lena Clark, lclark@wardcc.com
Investor Contacts:
American Electric Technologies, Inc.
John Untereker, 713-644-8182
juntereker@aeti.com

Featured Product

TRA SNOW AND SUN - SOLAR TILE MOUNT

TRA SNOW AND SUN - SOLAR TILE MOUNT

You haven't installed a tile mount that is easier to install than the Solar Tile Mount manufactured by TRA Snow and Sun. Solar Tile Mount is used on all tile roof profiles: flat, mid, and high. It is made in the USA of aluminum alloy for strength and excellent corrosion resistance. Solar Tile Mount is built to allow more ease in installation with more rise from the tile surface to the rail for better air flow below panels. The adjustable base is longer than most allowing attachment 6" to the left or right to have the bracket in the base of the pan of the tile and still fasten to the rafter. Solar Tile Mount is adjustable for counter batten systems from ¾" to 3". The horizontal rail is directly above base fasteners giving greater uplift resistance than any other system. For superior waterproofing apply TRA Snow and Sun's butyl backed VersaFlash aluminum flashing. No tile flashing is needed on top of the tile for greater labor and material cost savings.