TÜV certifies SST Hydrochlorination-Polysilicon production technology under scrutiny

Under observation of the team around Dr. Hartmut Neumann from TÜV Sued Industrieservice GmbH, the hydrochlorination process for the synthesis of trichlorosilane at the production plant of Schmid Silicon Technology in Saxony, Dresden has been tested for its conversion rate in December 2011.

The study was done under exceptional conditions: The operating parameters were lowered to the minimum settings in order to verify which is the absolute minimum conversion rate for the hydochlorination system under worst operating conditions. Accordingly, the hydrochlorination plant was running at only 50% of its nominal throughput in respect to STC consumption, and the reaction time of the fluidized bed reactor was reduced to 60%. Also, the reaction temperature was set to a minimum.


Considering that the plant has been running with minimal process parameters, an impressive conversion rate of 24.3% was achieved. Jochem Hahn, COO of SST: "We are very proud to prove to the polysilicon world the effectiveness of our low pressure hydrochlorination system. Our state of the art low pressure hydrochlorination serves a lot of advantages to our customers in respect to operation, safety and cost compared to conventional high pressure systems." Since polysilicon manufacturers need the flexibility to adjust their production output according to the market conditions it's important for them to know the performance of the plant if running at reduced capacity.

The TÜV experts also confirm in the certificate that operating the hydrochlorination plant at full capacity with normal temperatures and under normal conditions will enhance the conversion rate of STC, and therefore the output of TCS, significantly. Jochem Hahn, COO of SST: "We are able to confirm a 26.8 % conversion rate in production with an even further upside potential."

With the start of production of the hydrochlorination plant in September 2011, Schmid Silicon Technology within just 4 months successfully completed the commissioning of its own monosilane-based production facility for polysilicon manufacturing. Herewith SST closes the entire production cycle beginning from metallurgical silicon and ending with high-purity, 11N electronic-grade polysilicon.


About Schmid Silicon Technology GmbH (SST):
Founded in 2006 by Christian Schmid, SST is about to enter in a strong growth phase. Schmid Silicon Technology is the leading technology provider with respect to high-end solar (and, if demanded, electronic) grade polysilicon and monosilane gas production as well as plant engineering (turnkey).
In addition to the patented technology SST supplies together with its partner M+W Group the overall know-how for planning and realization of turnkey plants for the polysilicon and monosilane production.
Project planning and realization for polysilicon and monosilane productions are among SST's core expertise (starting with the pre-basic design and ending with the qualification of the key staff and after sales services).
Furthermore, SST supplies single-equipment for polysilicon production. SST will enable polysilicon-producers to achieve cost reductions of up to 40% compared to traditional production methods.
Schmid Silicon Technology GmbH is the only equipment supplier investing in its own technology. The company operates Schmid Polysilicon Production GmbH in Saxony, Germany, designed to showcase its advanced Monosilane Technology. This worldwide unique polysilicon plant allows an optimal technology design as well as continuous process improvement and new technological innovations.

Featured Product

GreenFasten™ solar panel roof mount hardware, watertight, USA made

GreenFasten™ solar panel roof mount hardware, watertight, USA made

The GreenFasten™ - GF1 system utilizes the patented watertight technology EcoFasten Solar® is known for. The flashing is fit with our EPDM rubber bushing and when used with a compatible EcoFasten Solar compression bracket (milled with countersink), a watertight seal is created, which protects the integrity of the roof. Requiring just a single fastener (lag bolt or self-drilling), GreenFasten provides the fastest install in the industry and will not void roofing manufacturer's warranties. Backed by IAPMO certification, GreenFasten delivers a mounting solution for all new or existing (retrofit) composition shingle roofs, and is the most cost-effective solution available. Like all of the solar roof mount solutions in our line of products, GreenFasten is made in the USA using recycled materials.