Making colorful buildings that convert solar light into energy

Researchers create new shades for a solar-light-absorbing surface that combine form and function

WASHINGTON--By converting sunlight into usable energy, solar thermal devices could become an important part of a sustainable future. To that end, researchers have developed a new solar-light-absorbing surface that can have almost any design, pattern, and color - useful for turning building facades and roofs into energy-capturing exteriors without sacrificing aesthetics.


Since they also use similar materials as existing solar absorbers, this new kind of solar absorber could lead to wider use of solar thermal technology and more energy efficiency, said Shao-Wei Wang, Shanghai Institute of Technical Physics, China. Wang and his colleagues describe their design in Optics Express, a journal of The Optical Society (OSA). "A significant amount of energy might come from our building facades and roofs," he said.

One of the most common uses of solar thermal technology is to heat water, allowing for an enjoyable hot shower or a dip in a warm swimming pool. Hot water could also heat buildings during winter. Additionally, solar thermal technology can generate electricity. While solar panels convert sunlight directly into electricity, solar thermal devices use sunlight to first boil a liquid like water, producing gas or steam that drives power generators.

At the heart of this technology are layered surfaces called solar selective absorbers, which, as their name implies, are made from materials that absorb sunlight. To be efficient and hold onto heat, the emission of infrared light must be minimal. The problem with conventional absorbers is that the best ones are always black or dark blue. If you're hoping to incorporate the technology into a building, such a dark color doesn't always fit with the architecture and aesthetics. "A colorful world is much better than a monotonous dark one," Wang said.

Previous attempts at colorful solar absorbers have been limited. For example, the materials either couldn't absorb all wavelengths of sunlight or they emitted a lot of infrared. Each absorber also had to be the same color, making it expensive and difficult to design a facade with an image or a complex pattern.

The new absorber is covered with multiple layers of transparent dielectric materials, which can reflect light of a particular color. By changing the thickness of these layers, the researchers can tune the absorber to reflect light of almost any shade required. Some parts of the absorbing layer can be covered with a thicker transparent dielectric layer than other parts, allowing the researchers to create a single absorber with a rainbow of hues. And, it works almost as well as the best conventional ones.

In particular, the researchers made a square absorber 60 mm on each side. They covered the absorber with a mosaic of dielectric materials, forming a grid of 16 tiles. Each tile was of a different thickness - and thus a different color. Each tile, which could be made as small as one millimeter on each side, acts like a pixel on the absorber.

Using this methodology, an absorber with up to a thousand of these pixel-like color units - which would be virtually impossible with conventional absorbers - can be built and form almost any pattern you want, Wang said. For example, you could make a camouflage pattern, which would be useful for making solar thermal devices for the military.

While the technology isn't market-ready yet, he said that with enough industry investment, the methods could be commercialized in the near future.

Paper: F. Chen, S. Wang, X. Liu, R. Ji, Z. Li, X. Chen, Y. Chen, W. Lu, "Colorful solar selective absorber integrated with different colored units," Optics Express 40, A92-103 (2016)

About Optics Express
Optics Express reports on new developments in all fields of optical science and technology every two weeks. The journal provides rapid publication of original, peer-reviewed papers. It is published by The Optical Society and edited by Andrew M. Weiner of Purdue University. Optics Express is an open-access journal and is available at no cost to readers online at: OpticsInfoBase.

About The Optical Society
Founded in 1916, The Optical Society (OSA) is the leading professional organization for scientists, engineers, students and entrepreneurs who fuel discoveries, shape real-life applications and accelerate achievements in the science of light. Through world-renowned publications, meetings and membership initiatives, OSA provides quality research, inspired interactions and dedicated resources for its extensive global network of optics and photonics experts. OSA is a founding partner of the National Photonics Initiative and the 2015 International Year of Light. For more information, visit: www.osa.org.

Featured Product

WS510 Secondary Standard

WS510 Secondary Standard

In the monitoring of large photovoltaic (Utility Scale), in assessing potential sites (Solar-assessment), or in up and coming electricity cost saving initiatives projects (Commercial & Industrial), the WS510 now provides the market a secondary standard pyranometer, ultrasonic wind speed, ultrasonic wind direction, temperature, pressure and humidity all in a single unit.. This sensor meets the high demands of the world meteorological organization (WMO) through the active valving at air temperature measurement and the inertia- and maintenance-free measurement of wind speed and wind direction on the ultrasonic principle. Equipped with a Kipp & Zonen pyranometer of the secondary standards, the WS510-UMB Compact weather sensor from Lufft unites the precision of a variety of meteorological individual sensors in a single all-in-one device, for the first time.